Parking lot marking is very important because it assists in directing drivers into the designated spaces in which they are required to park their cars. Parking lot stripping is usually done in the parking spaces for businesses, schools, hospitals, and other organizations. Even public parking spaces are usually marked correctly according to the laws observed within the jurisdiction. To perform this process well, there are a few factors that need to be given attention. When in need of professionals in Parking lot marking Arkansas should be visited.
Firstly, one is required to have knowledge on the nature of the laws that exist within their jurisdiction. These laws determine a variety of aspects like the dimension of parking lots, accessibility of the facility, width of the marking lines, and paint color among many others. A standard stall should be 18 feet long and 9 feet wide although the measurements may vary based on the jurisdiction under consideration.
Lots normally contain aisles which allow drivers to have easy access to stalls. These aisles offer drivers enough space for maneuvering around the lot and backing out from their parking spots. Two-way drive aisle is supposed to have a minimum width of 24 feet. On the contrary, the width of a two way-drive aisle is supposed to be 12 feet. These are the standard measurements of stalls that are placed at a certain angle. The aisle width should increase with increase in the angle of the stalls towards 90 degrees.
According to the US federal standards, the standard color for marking lots is white. For demarcating the locations which are unavailable for parking, the yellow color should be used. These consist of painted islands, which are situated at the ends of lots. The blue color is used to mark handicapped-accessible spaces. Lastly the red color is used in demarcating fire lines where individuals are banned from parking their vehicles.
There are two major reasons as to why stripping is done and they are safety and aesthetics. Aesthetics are achieved by using colorful colors in a meticulous manner to mark pavements. Safety is assured as well since drivers are directed by the markings, which helps to reduce accidents. The markings also make sure that space is utilized in an economical way.
When one is applying paint on concrete substrates, the best choice of paint to use is chlorinated rubber paint for the best adherence. On the other hand, fresh sealer or asphalt requires water-borne coating. Re-stripping can be done using various kinds of paint, but set-quick acrylic waterborne paints are the best choice. Acrylic paints should be applied at 45 degrees F.
Airless stripping equipment should be used in the application of the paint. The marks should be 13mm wide. It is possible for the surface to absorb the paint thereby causing the applied marks to become thin in the end. A typical paint application will need at least 30 minutes to dry totally and be ready for use.
One is better off applying two thin coats of the paint as opposed to one thick coat. When the marks lose their visibility to 75 percent, it is time to re-strip. The right material should be used to return the marks to their initial level of visibility.
Firstly, one is required to have knowledge on the nature of the laws that exist within their jurisdiction. These laws determine a variety of aspects like the dimension of parking lots, accessibility of the facility, width of the marking lines, and paint color among many others. A standard stall should be 18 feet long and 9 feet wide although the measurements may vary based on the jurisdiction under consideration.
Lots normally contain aisles which allow drivers to have easy access to stalls. These aisles offer drivers enough space for maneuvering around the lot and backing out from their parking spots. Two-way drive aisle is supposed to have a minimum width of 24 feet. On the contrary, the width of a two way-drive aisle is supposed to be 12 feet. These are the standard measurements of stalls that are placed at a certain angle. The aisle width should increase with increase in the angle of the stalls towards 90 degrees.
According to the US federal standards, the standard color for marking lots is white. For demarcating the locations which are unavailable for parking, the yellow color should be used. These consist of painted islands, which are situated at the ends of lots. The blue color is used to mark handicapped-accessible spaces. Lastly the red color is used in demarcating fire lines where individuals are banned from parking their vehicles.
There are two major reasons as to why stripping is done and they are safety and aesthetics. Aesthetics are achieved by using colorful colors in a meticulous manner to mark pavements. Safety is assured as well since drivers are directed by the markings, which helps to reduce accidents. The markings also make sure that space is utilized in an economical way.
When one is applying paint on concrete substrates, the best choice of paint to use is chlorinated rubber paint for the best adherence. On the other hand, fresh sealer or asphalt requires water-borne coating. Re-stripping can be done using various kinds of paint, but set-quick acrylic waterborne paints are the best choice. Acrylic paints should be applied at 45 degrees F.
Airless stripping equipment should be used in the application of the paint. The marks should be 13mm wide. It is possible for the surface to absorb the paint thereby causing the applied marks to become thin in the end. A typical paint application will need at least 30 minutes to dry totally and be ready for use.
One is better off applying two thin coats of the paint as opposed to one thick coat. When the marks lose their visibility to 75 percent, it is time to re-strip. The right material should be used to return the marks to their initial level of visibility.
About the Author:
You can find a summary of the advantages you get when you use professional parking lot marking Arkansas services at http://www.arrowstriping-nwa.com today.
No comments:
Post a Comment