When you want to show off your lawn, there is nothing nicer than having clear cut areas that define the separation between turf and flowerbeds or other formations. There are many towns and neighborhood associations that reward those that spend the time it takes to create a beautiful looking lawn. With a plastic bender board, you can create that clean separation with ease and keep the weeds from encroaching on your beds.
Two different types exist and are in use today. The first is made from packed wood fibers and other natural materials. Though it is a great way to create the border, it will have to be replaced over time because it is designed to decay and work its way into the soil. The plastic type will not decay over time and is environmentally sound because it is made of recycled plastics that would be headed to the landfill. It will last much longer and keep doing its job for years.
Start by measuring how much you are going to need. An easy way to do this is to put a stake in the ground at each major twist and turn. Put a string on one stake and then attach it along the way. Finally, measure how much string you used, add a few inches just in case, and that should provide you with enough material to do the job.
When you are done measuring and getting the material, it is time to dig. The hole should be about six inches wide and deep enough for the whole board to sit below the surface. Don't dispose of the dirt because you are going to need it at the end to fill the hole back in.
The third step is to place stakes along the path. These should be inside the trench and placed so the border material will be on the turf side. If you have a break in the material, place two stakes near each other to help hold the two ends together. This will prevent them from separating and causing a gap.
Place the material in the ground. The easiest way to do this is simply to roll it out along the trench and then push it into the hole. Head back to the start and begin securing it to the stakes along the path. Make sure any areas that stick above the level surface are pushed down or dig out a little bit of dirt to help it sit lower. As you approach the end, you may find you have a bit too much material. You can easily cut this off with a box cutter or hack saw and place it snug in the end.
Use the dirt to fill the trench. Using a rake or shovel, fill in the trench until the dirt is all used up. There should be quite a bit left over and a nice mound will be on top. This fine since the dirt will settle in a few days. Pack it in by stomping on it or using a stamp or rake. After a few days of settling, you can begin to place stones on top if you want to create a nice visible border.
Now you are done. You have successfully placed a border between your grass and other landscaping. This will help keep the weeds out and let you avoid mowing up into the flowerbeds. The border will help prevent weeds and provide the needed separation between the beds and the grass.
Two different types exist and are in use today. The first is made from packed wood fibers and other natural materials. Though it is a great way to create the border, it will have to be replaced over time because it is designed to decay and work its way into the soil. The plastic type will not decay over time and is environmentally sound because it is made of recycled plastics that would be headed to the landfill. It will last much longer and keep doing its job for years.
Start by measuring how much you are going to need. An easy way to do this is to put a stake in the ground at each major twist and turn. Put a string on one stake and then attach it along the way. Finally, measure how much string you used, add a few inches just in case, and that should provide you with enough material to do the job.
When you are done measuring and getting the material, it is time to dig. The hole should be about six inches wide and deep enough for the whole board to sit below the surface. Don't dispose of the dirt because you are going to need it at the end to fill the hole back in.
The third step is to place stakes along the path. These should be inside the trench and placed so the border material will be on the turf side. If you have a break in the material, place two stakes near each other to help hold the two ends together. This will prevent them from separating and causing a gap.
Place the material in the ground. The easiest way to do this is simply to roll it out along the trench and then push it into the hole. Head back to the start and begin securing it to the stakes along the path. Make sure any areas that stick above the level surface are pushed down or dig out a little bit of dirt to help it sit lower. As you approach the end, you may find you have a bit too much material. You can easily cut this off with a box cutter or hack saw and place it snug in the end.
Use the dirt to fill the trench. Using a rake or shovel, fill in the trench until the dirt is all used up. There should be quite a bit left over and a nice mound will be on top. This fine since the dirt will settle in a few days. Pack it in by stomping on it or using a stamp or rake. After a few days of settling, you can begin to place stones on top if you want to create a nice visible border.
Now you are done. You have successfully placed a border between your grass and other landscaping. This will help keep the weeds out and let you avoid mowing up into the flowerbeds. The border will help prevent weeds and provide the needed separation between the beds and the grass.
About the Author:
When you are looking for information about plastic bender board, come to our web pages online today. More details are available at http://www.bestedging.com now.
No comments:
Post a Comment